工業冷水機注意事項
工業冷水機注意事項：工業冷水機是較為復雜的設備，甚至連開關機都有流程，如果不能夠根據規范來操作、亦沒有專人保養，必然會導致冷水機的制冷效率下降、甚至?xí)蟠蠼档屠渌畽C的使用壽命。下面，達安泰公司來說說企業使用工來冷水機的幾個注意事項！

除了上面說到的企業應該安排專人負責制冷機啟停、開關以及維修和保養之外，企業使用制冷機的注意事項分別有以下幾個方面：

工業冷水機注意事項溫度與壓力
可以說，溫度與壓力相關的參數，是冷水機*為重要的參數，企業應該注意冷水機的溫度與壓力相關的參數，有問題及時解決，避免影響冷水機正常運行。

正常情況下，冷媒并非易耗品，所以不會經常性缺失，若經常性或突然性的缺失，建議檢查冷水機的冷媒是否出現泄露問題，如果有泄露問題，應該及時找到泄漏點，并進行補漏，或更換相關冷媒管路、連接件，必要時，還應該進行強制通風處理。

工業冷水機注意事項注意冷水機的負載
工業冷水機的負載，說白了，并不僅僅是壓縮機的負載，壓縮機要與包括冷凝器、蒸發器、膨脹閥等機件進行配合才能夠正常制冷，水泵以及水塔或風冷式冷水機的風機系統等，這些都是互相配合的，若冷水機負載超標，不會僅僅是壓縮機不夠用，其它各個機件和部件，都會出現壓力過大的問題！工業冷水機的負載較大，或者說超過額定負載，造成過載的現象，會影響較嚴重的問題，包括制冷效率下降、噪音變大、震動幅度變大、電資源消耗過大、壽命降低等等一系列問題，需要注意！

工業冷水機注意事項冷媒泄露
冷媒泄露不僅僅會導致冷水機的制冷效率產生影響，更可能會因為冷媒泄露而影響進出機房的相關人員的健康，所以冷媒泄露問題一定要注意。

注意以上講到的注意點，對延長冷水機的使用壽命、提高制冷效率、提高冷水機使用**，有異乎尋常的重要性！
Industrial chiller Note: Industrial chiller is a more complex equipment, and even the switch machine has a process, if not according to the norms to operate, there is no special maintenance, will inevitably lead to chillers cooling efficiency decline, or even greatly reduced The life of the chiller. Here, the company to say that the company to use the workers to the cold water machine a few notes!

In addition to the above mentioned enterprises should arrange for the person responsible for the start-up of the refrigerator, switches and maintenance and repair, the use of refrigerators business considerations are the following aspects:

Industrial chiller Note First, the temperature and pressure
It can be said that the temperature and pressure-related parameters, is the most important parameters of the chiller, enterprises should pay attention to the temperature and pressure of the chiller parameters, a timely solution to the problem, to avoid affecting the normal operation of the chiller.

Under normal circumstances, the refrigerant is not consumables, so there will be no frequent missing, if the frequent or sudden missing, it is recommended to check the chiller refrigerant leak problems, if there is a leak, you should find a leak point and Trap, or replace the relevant refrigerant piping, connecting parts, if necessary, should also be forced ventilation.

Industrial chillers Note the load of the chiller
Industrial chiller load, said white, and not just the compressor load, the compressor and including the condenser, evaporator, expansion valve and other parts to be able to normal cooling, water pumps and water towers or air-cooled chiller Of the fan system, which are all with each other, if the chiller overload, not just the compressor is not enough, the other parts and parts, there will be too much pressure on the problem! If the load of the industrial chiller is large or exceeds the rated load, the overload phenomenon will affect the more serious problems, including the decrease of the cooling efficiency, the larger the noise, the larger the vibration amplitude, the excessive consumption of the electrical resources, the lower life expectancy A series of questions that need attention!

Industrial chiller notes refrigerant leakage
Refrigerant leakage will not only lead to the cooling efficiency of the chiller, but also because of the refrigerant leakage and affect the health of the relevant personnel into and out of the engine room, so the refrigerant leakage problem must pay attention.

Note that the above mentioned points of attention, to extend the service life of chillers, improve the efficiency of refrigeration, improve the safety of the use of chillers, there is an unusual importance!